Solution for an issue with exhaust system

kshaft revolution. The 4 processes of intake, compression, power and exhaust take place in only 2 strokes so that it is not possible to dedicate a stroke exclusively for each of them. Starting at TDC the cycle consist of: P

Solution for an issue with exhaust system Mclaren smoking exhaust

The defining characteristic

2-stroke engines
Main article: 2-stroke engine

The defining characteristic of this kind of engine is that each piston completes a cycle every crankshaft revolution. The 4 processes of intake, compression, power and exhaust take place in only 2 strokes so that it is not possible to dedicate a stroke exclusively for each of them. Starting at TDC the cycle consist of:

Power: While the piston is descending the combustion gases perform work on it?as in a 4-stroke engine?. The same thermodynamic considerations about the expansion apply.
Scavenging: Around 75° of crankshaft rotation before BDC the exhaust valve or port opens, and blowdown occurs. Shortly thereafter the intake valve or transfer port opens. The incoming charge displaces the remaining combustion gases to the exhaust system and a part of the charge may enter the exhaust system as well. The piston reaches BDC and reverses direction. After the piston has traveled a short distance upwards into the cylinder the exhaust valve or port closes; shortly the intake valve or transfer port closes as well.
Compression: With both intake and exhaust closed the piston continues moving upwards compressing the charge and performing a work on it. As in the case of a 4-stroke engine, ignition starts just before the piston reaches TDC and the same consideration on the thermodynamics of the compression on the charge.

While a 4-stroke engine uses the piston as a positive displacement pump to accomplish scavenging taking 2 of the 4 strokes, a 2-stroke engine uses the last part of the power stroke and the first part of the compression stroke for combined intake and exhaust. The work required to displace the charge and exhaust gases comes from either the crankcase or a separate blower. For scavenging, expulsion of burned gas and entry of fresh mix, two main approaches are described: Loop scavenging, and Uniflow scavenging, SAE news published in the 2010s that 'Loop Scavenging' is better under any circumstance than Uniflow Scavenging.6

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


Ignition

Ignition

Internal combustion engines require ignition of the mixture, either by spark ignition (SI) or compression ignition (CI). Before the invention of reliable electrical methods, hot tube and flame methods were used. Experimental engines with laser ignition have been built.15
Spark Ignition Process
Bosch Magneto
Points and Coil Ignition

The spark ignition engine was a refinement of the early engines which used Hot Tube ignition. When Bosch developed the magneto it became the primary system for producing electricity to energize a spark plug.16 Many small engines still use magneto ignition. Small engines are started by hand cranking using a recoil starter or hand crank . Prior to Charles F. Kettering of Delco's development of the automotive starter all gasoline engined automobiles used a hand crank.17

Larger engines typically power their starting motors and Ignition systems using using the electrical energy stored in a lead?acid battery. The battery's charged state is maintained by an automotive alternator or (previously) a generator which uses engine power to create electrical energy storage.

The battery supplies electrical power for starting when the engine has a starting motor system, and supplies electrical power when the engine is off. The battery also supplies electrical power during rare run conditions where the alternator cannot maintain more than 13.8 volts (for a common 12V automotive electrical system). As alternator voltage falls below 13.8 volts, the lead-acid storage battery increasingly picks up electrical load. During virtually all running conditions, including normal idle conditions, the alternator supplies primary electrical power.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


What to buy a gift for fans of the automotive industry?

Buying a gift can be a problem, especially if we want to make a gift without obligation, but still quite meaty and really interesting for the recipient. What buy a fan of the automotive industry? Certainly a nice gift idea for such a person is choosing a book in this field. However, one should check if the person you want to give away no longer has such a home. Available on the market, however, is much different proposals in this regard, that will certainly find something suitable, as well as inexpensive. The book is a very good gift idea for people of all ages, and entered at the start of commemorative dedication certainly will constitute a kind of souvenir. So let's decide on the choice of books, if you are looking for an idea for a gift for a fan of the automotive industry.



© 2019 http://posrednik.walbrzych.pl/